Frizair - Installation


Window A/C Window A/C with remote Split A/C Coolers Coils

INSTALLATION DETAILS

Type	A

Customer arranges to keep the wooden frame ready (of inside dimensions 676 x 458 mm), Cross section 75 x 50 mm
Only fixing of outer cabinet in wooden frame & commissioning is to be done.
No carpentry / grill cutting work is required.

Cost of installation would be Rs.200/-

Type	B

Before

After

Provision & Wooden frame for installation of A/c already exists.
Only minor correction (up to 50mm) in inside dimensions of wooden frame are required.
Modification to grill is not included.

Cost of installation would be Rs.400/-

Type	C

Before

After

For a typical window size of approximately 3’ x 4’ without provision for fitting air conditioner readily.
Unpainted wooden frame of size 676mm x 458mm (inside) with a cross section of 75 x 50 made from Assam/Medium teak wood.
Covering made of unpainted good quality non water-proof plywood of 6mm thickness
Modification to grill is not included.

Cost of installation would be Rs.750/-

Type	D

For a typical window of size 6’ x 4’ and without provision for fitting air conditioner readily.
Unpainted wooden frame of size 676 x 458 (inside) with a cross section of 75 x 50 from Assam/Medium Teak wood.

Covering made of unpainted good quality water-proof plywood of 6mm thickness.

Cost of installation would be Rs.1000/-

Before

After

Type	E

Wall Breakage
In case the wall is to be broken to install the Air conditioner, the customer must arrange the civil work. We will supply the wooden frame and install the Air conditioner in it.
Cost of installation would be Rs.750/-
(including wooden frame)

Note: In case customer provides suitable opening installation would be done as per type A and will cost Rs.200/- only.

For your
information

In case the customer specifies material for frame and ply, different from the specifications given, extra charges will be levied.
Modifications to grill will be as per site requirements. These charges will be extra at nominal rates.

This can be quoted separately by the dealer.

While every effort would be made to carry out the work to best of our abilities, the risk of any damage to the premises during installation lies entirely with the customer. Our carpenters will not be able to do furniture quality carpentry and cannot match high quality interior finishes.

For your installation requirements talk to :

All information provided here are subject to change without notice due to our continuous improvement efforts.

POWER SUPPLY:

In order to enable the efficient and trouble-free of your air conditioner, connect the power plug of your air conditioner through an exclusive circuit, having a fuse or an MCB (Miniature Circuit breaker) of the correct capacity.

FUSE/MCB SPECIFICATIONS:

FV-100 / FHW-100(1.0 ton)

15A
FV-150 / FHW (1.5ton)

20A
FV-175(1.75ton)

20A
FV-200/FHW-200(2.0 ton)

25A

WARNING:

Ensure that the unit is properly earthed and that right hand side of the terminal of the socket is the "phase" or the "live" terminal. Any switch or MCB should be in series with this terminal and NOT in series with the "Neutral" terminal.
House wiring should conform to the specifications mentioned in the following table(distances are from the electricity meter to the electrical point.)

Electrical Power requirements to be provided by the customer:

Power point should be within 1 metre from bottom right corner of air conditioner.
Electrical wiring & MCB as follows:

Model	Up to 12 Metres	12-24 Metres	24-36 Metres	36-48 Metres

FV-100 FV-150 FV-175 FV-200	3/20 3/18 3/18 3/18	3/18 7/18 7/18 7/18	7/20 7/18 7/18 7/16	7/18 7/16 7/16 7/16

Note : The above designation represents the number and diameter (in S.W.G) of wires forming the cable e.g 3/20 indicated 3 wires, each of 20 S.W.G in cable.

Web Design by INDAX